block_device_mappings

block_device_mappings
  • (list) --

    Any block device mapping entries.

    • (dict) --

      Describes a block device mapping, which defines the EBS volumes and instance store volumes to attach to an instance at launch.

      • DeviceName (string) --

        The device name (for example, /dev/sdh or xvdh ).

      • VirtualName (string) --

        The virtual device name ( ephemeral N). Instance store volumes are numbered starting from 0. An instance type with 2 available instance store volumes can specify mappings for ephemeral0 and ephemeral1 . The number of available instance store volumes depends on the instance type. After you connect to the instance, you must mount the volume.

        NVMe instance store volumes are automatically enumerated and assigned a device name. Including them in your block device mapping has no effect.

        Constraints: For M3 instances, you must specify instance store volumes in the block device mapping for the instance. When you launch an M3 instance, we ignore any instance store volumes specified in the block device mapping for the AMI.

      • Ebs (dict) --

        Parameters used to automatically set up EBS volumes when the instance is launched.

        • DeleteOnTermination (boolean) --

          Indicates whether the EBS volume is deleted on instance termination. For more information, see Preserving Amazon EBS volumes on instance termination in the Amazon EC2 User Guide .

        • Iops (integer) --

          The number of I/O operations per second (IOPS). For gp3 , io1 , and io2 volumes, this represents the number of IOPS that are provisioned for the volume. For gp2 volumes, this represents the baseline performance of the volume and the rate at which the volume accumulates I/O credits for bursting.

          The following are the supported values for each volume type:

          • gp3 : 3,000-16,000 IOPS
          • io1 : 100-64,000 IOPS
          • io2 : 100-64,000 IOPS

          For io1 and io2 volumes, we guarantee 64,000 IOPS only for Instances built on the Nitro System. Other instance families guarantee performance up to 32,000 IOPS.

          This parameter is required for io1 and io2 volumes. The default for gp3 volumes is 3,000 IOPS. This parameter is not supported for gp2 , st1 , sc1 , or standard volumes.

        • SnapshotId (string) --

          The ID of the snapshot.

        • VolumeSize (integer) --

          The size of the volume, in GiBs. You must specify either a snapshot ID or a volume size. If you specify a snapshot, the default is the snapshot size. You can specify a volume size that is equal to or larger than the snapshot size.

          The following are the supported volumes sizes for each volume type:

          • gp2 and gp3 :1-16,384
          • io1 and io2 : 4-16,384
          • st1 and sc1 : 125-16,384
          • standard : 1-1,024
        • VolumeType (string) --

          The volume type. For more information, see Amazon EBS volume types in the Amazon EC2 User Guide . If the volume type is io1 or io2 , you must specify the IOPS that the volume supports.

        • KmsKeyId (string) --

          Identifier (key ID, key alias, ID ARN, or alias ARN) for a customer managed CMK under which the EBS volume is encrypted.

          This parameter is only supported on BlockDeviceMapping objects called by RunInstances, RequestSpotFleet, and RequestSpotInstances.

        • Throughput (integer) --

          The throughput that the volume supports, in MiB/s.

          This parameter is valid only for gp3 volumes.

          Valid Range: Minimum value of 125. Maximum value of 1000.

        • OutpostArn (string) --

          The ARN of the Outpost on which the snapshot is stored.

          This parameter is only supported on BlockDeviceMapping objects called by CreateImage.

        • Encrypted (boolean) --

          Indicates whether the encryption state of an EBS volume is changed while being restored from a backing snapshot. The effect of setting the encryption state to true depends on the volume origin (new or from a snapshot), starting encryption state, ownership, and whether encryption by default is enabled. For more information, see Amazon EBS encryption in the Amazon EC2 User Guide .

          In no case can you remove encryption from an encrypted volume.

          Encrypted volumes can only be attached to instances that support Amazon EBS encryption. For more information, see Supported instance types.

          This parameter is not returned by DescribeImageAttribute.

          For CreateImage and RegisterImage, whether you can include this parameter, and the allowed values differ depending on the type of block device mapping you are creating.

          • If you are creating a block device mapping for a new (empty) volume , you can include this parameter, and specify either true for an encrypted volume, or false for an unencrypted volume. If you omit this parameter, it defaults to false (unencrypted).
          • If you are creating a block device mapping from an existing encrypted or unencrypted snapshot , you must omit this parameter. If you include this parameter, the request will fail, regardless of the value that you specify.
          • If you are creating a block device mapping from an existing unencrypted volume , you can include this parameter, but you must specify false . If you specify true , the request will fail. In this case, we recommend that you omit the parameter.
          • If you are creating a block device mapping from an existing encrypted volume , you can include this parameter, and specify either true or false . However, if you specify false , the parameter is ignored and the block device mapping is always encrypted. In this case, we recommend that you omit the parameter.
      • NoDevice (string) --

        To omit the device from the block device mapping, specify an empty string. When this property is specified, the device is removed from the block device mapping regardless of the assigned value.